, ,

1.85mm Male to 2.92mm(K,SK) Female Millimeter-Wave Adapter | Ultra, DC-40GHz, Stainless Steel

$271.00

+ Free Shipping

DC–40 GHz · 50 Ω · VSWR 1.15 max
1.85mm Male to 2.92mm(K,SK) Female Millimeter-Wave Adapter — passivated stainless steel 316F body.

SKU: RA4011H Categories: , ,

RA4011H joins 1.85mm male to 2.92mm female, a single straight body rated to 40 GHz at 50 ohms. The headline figures are a VSWR of 1.15:1 maximum and an insertion loss of 0.25 dB, all specified across the full DC to 40 GHz band rather than at spot frequencies. One end is male and the other female, so the direction is fixed: the pin goes into the port that expects it, and the part cannot be reversed. One-piece construction is the point: every extra mating plane is another reflection, and this part replaces a stack of them with a single joint. The straight body keeps the run axial, which is the lowest-loss, lowest-stress way to join two ports. It is built in the Ultra tier, the tightest tolerance class of this interface family, intended for daily precision work.

Specifications

  • Interface A: 1.85mm male
  • Interface B: 2.92mm female
  • Frequency: DC to 40 GHz
  • Impedance: 50 ohm
  • VSWR: 1.15:1 maximum
  • Insertion loss: 0.25 dB maximum
  • Body: stainless steel
  • Weight: 0.03 kg
  • Grade: Ultra

Where it is used

Production fixtures rely on it where a panel-mounted port has to meet a cable of another series, day after day. It also earns its place in system integration, where two sub-assemblies with different connectors have to be joined without a custom cable.

The adapter is also the sacrificial part in a wear path: replace it when the match drifts instead of replacing the instrument port.

40 GHz is where air-dielectric construction earns its price; a PTFE interface would not hold the match this far up.

Compatibility and mating

1.85mm (V) mates 2.4mm and other 1.85mm parts, and nothing below that: SMA and 2.92mm look similar but will not mate correctly. Torque to about 0.9 N·m and keep the mating plane spotless.

Each end keeps its own interface standard, which is why the part number lists both series rather than a single connector type.

Keep the mating faces clean and dry, and inspect them under a loupe before a critical measurement; most ‘bad’ adapters are dirty ones.

Ordering

The SKU is the order code. If you need a different interface pair, a different gender combination or a longer body, ask before ordering rather than adapting this part on site.

Frequently asked questions

How many mating cycles will it take?
Precision interfaces are usually rated in the hundreds to a thousand cycles, and the exact figure is in the datasheet. Wear shows first as a rise in return loss.

Can I mate it with a different precision series?
Only where the standards are mechanically compatible. SMA, 3.5mm and 2.92mm intermate; 2.4mm and 1.85mm intermate; mixing across those two groups damages the precision side.

Is it 50 or 75 ohm?
This part is 50 ohm. A 75 ohm system needs a matching pad or a 75 ohm part; the two impedances are not interchangeable on a threaded interface of the same size.

Does an adapter add loss?
Yes, a small amount. The datasheet gives the maximum insertion loss for this part; at these frequencies it is usually a few tenths of a dB, but it belongs in the budget.

Does it work at DC?
Yes, it is a passive coaxial through-connection, so it passes DC as well as RF unless the datasheet says otherwise.

RA4011H datasheet preview – click to view full PDF

Weight 0.03 kg
Dimensions 6 × 3 × 3 cm
Connector Type

,

Max Frequency

Series

Reviews

There are no reviews yet.

Be the first to review “1.85mm Male to 2.92mm(K,SK) Female Millimeter-Wave Adapter | Ultra, DC-40GHz, Stainless Steel”

Your email address will not be published. Required fields are marked *