,

2.92mm(K,SK) Millimeter-Wave Coaxial Fixed Attenuator | Economy, DC-40GHz, 2 W, 1-30 dB, Bidirectional, Male-Female, Round, Stainless Steel Connector

$240.00

+ Free Shipping
SKU: R402E-XX Categories: ,

The R402E-XX pads a 2.92mm line by 1-30 dB with a 2 W body, from DC to 40 GHz. The headline figures are a VSWR of 1.3:1 maximum, attenuation over 1-30 dB and 2 W of dissipation, all specified across the full DC to 40 GHz band rather than at spot frequencies. The in-line body sits between the two connectors and keeps the run straight, so the pad drops the level without adding a bend to the path. It is built in the Economy tier, the value build, keeping the same interface dimensions at a lower price point.

Specifications

  • Interface: 2.92mm, male to female
  • Attenuation: 1-30 dB
  • Power: 2 W
  • Frequency: DC to 40 GHz
  • Impedance: 50 ohm
  • VSWR: 1.3:1 maximum
  • Body: stainless steel
  • Centre contact: gold-plated beryllium copper centre contact
  • Weight: 0.05 kg
  • Grade: Economy

Where it is used

It is also a matching tool: a pad improves the effective return loss seen by either side of the connection. Bench set-ups use it to bring a strong source down to the level a receiver or analyser wants, without touching the source setting.

Because it is passive and has no controls, it cannot be knocked out of setting between shifts, which matters on a production line.

40 GHz is where air-dielectric construction earns its price; a PTFE interface would not hold the match this far up.

Compatibility and mating

The 2.92mm interface is mechanically compatible with SMA and 3.5mm, which is convenient and also the main risk: a worn SMA plug can damage a precision 2.92mm socket. Inspect before every mating and torque to about 0.9 N·m.

Nothing special is needed to mate it: clean the interfaces, torque to the figure for the series, and support the body so the connectors do not carry its weight.

Check the interface with a gauge after any drop. A part that has been dropped usually looks fine and measures badly.

Ordering

Every unit ships with its datasheet, and the outline drawing in it is the reference for panel cut-outs and mounting hole spacing. Check it before designing a fixture around the part.

Frequently asked questions

Can I get a different value?
The value range in the title is what this listing covers. Other values in the same family are separate SKUs; ask if you need a step that is not listed.

How accurate is the attenuation value?
The nominal value is held within the tolerance printed in the datasheet, typically a few tenths of a dB at low frequencies and wider at the top of the band.

Why does it get warm?
It converts the removed power into heat. A warm body at rated power is normal; a hot body means the rating or the derating is being ignored.

Does it need calibration?
No. A fixed pad has no adjustable parts; its value is set by the resistive element. Re-verify it only if a measurement looks suspicious.

How much power can it take?
The rating above is continuous, in free air. Derate it if the body is enclosed or sits next to another heat source, and never exceed it even briefly.

R402E-XX datasheet preview – click to view full PDF

Weight 0.05 kg
Dimensions 8 × 5 × 4 cm
Connector Type

Max Frequency

Series

Reviews

There are no reviews yet.

Be the first to review “2.92mm(K,SK) Millimeter-Wave Coaxial Fixed Attenuator | Economy, DC-40GHz, 2 W, 1-30 dB, Bidirectional, Male-Female, Round, Stainless Steel Connector”

Your email address will not be published. Required fields are marked *