,

BNC Medium-Power Coaxial Fixed Attenuator | Professional, DC-3GHz, 25 W, 1-60 dB, Unidirectional, Female Input, Female Output, Round, Tri-metal Plated Brass Connector

$197.00

+ Free Shipping
SKU: R3B25FF-XX Categories: ,

For level control on a BNC path, R3B25FF-XX provides 1-60 dB of fixed attenuation up to 3 GHz, in a 25 W package. The headline figures are a VSWR of 1.2:1 maximum, attenuation over 1-60 dB and 25 W of dissipation, all specified across the full DC to 3 GHz band rather than at spot frequencies. The in-line body sits between the two connectors and keeps the run straight, so the pad drops the level without adding a bend to the path. It is built in the Professional tier, the standard professional build for laboratory and production use.

Specifications

  • Interface: BNC, genders as listed
  • Attenuation: 1-60 dB
  • Power: 25 W
  • Frequency: DC to 3 GHz
  • Impedance: 50 ohm
  • VSWR: 1.2:1 maximum
  • Body: tri-metal plated brass
  • Centre contact: gold-plated beryllium copper centre contact
  • Weight: 0.05 kg
  • Grade: Professional

Where it is used

It protects front ends: a fixed pad in front of a sensitive input absorbs the mistake as well as the level. System builders fit it to equalise gain across a chain, or to bring two paths to the same reference level.

Because it is passive and has no controls, it cannot be knocked out of setting between shifts, which matters on a production line.

This is the low band, where the wavelength is long enough that connector geometry is forgiving and the match is set by the interface rather than the body.

Compatibility and mating

BNC is a bayonet interface: push and twist a quarter turn. It is fast, which is why video and lab racks still use it, but it is not a precision connection and should not be expected to hold a tight match at the top of its band.

Nothing special is needed to mate it: clean the interfaces, torque to the figure for the series, and support the body so the connectors do not carry its weight.

Store it capped. A mating plane that has collected grit will score the dielectric the first time it is torqued down.

Ordering

Every unit ships with its datasheet, and the outline drawing in it is the reference for panel cut-outs and mounting hole spacing. Check it before designing a fixture around the part.

Frequently asked questions

Does it work in both directions?
A fixed pad is reciprocal: the attenuation is the same either way. Direction only matters on the variable and directional parts, where the title states it.

Will it improve my return loss?
Yes, a pad isolates the two sides: a 6 dB pad improves the match seen by roughly 12 dB. That is why pads are used to stabilise a measurement.

How do I mount it?
Most fixed pads hang on the connector. Heavier bodies have mounting holes; support the part so the connectors do not carry its weight.

Is the DC path continuous?
Yes for a coaxial fixed pad: it passes DC as well as RF. Check the datasheet if your circuit cannot tolerate a DC path.

How much power can it take?
The rating above is continuous, in free air. Derate it if the body is enclosed or sits next to another heat source, and never exceed it even briefly.

R3B25FF-XX datasheet preview – click to view full PDF

Weight 0.05 kg
Dimensions 8 × 5 × 4 cm
Connector Type

Max Frequency

Reviews

There are no reviews yet.

Be the first to review “BNC Medium-Power Coaxial Fixed Attenuator | Professional, DC-3GHz, 25 W, 1-60 dB, Unidirectional, Female Input, Female Output, Round, Tri-metal Plated Brass Connector”

Your email address will not be published. Required fields are marked *