, ,

2.92mm(K,SK) Male to APC-7 Adapter | Economy, DC-18GHz, Stainless Steel

$231.00

+ Free Shipping

DC–18 GHz · 50 Ω · VSWR 1.25 max
2.92mm(K,SK) Male to APC-7 Adapter — passivated stainless steel body.

SKU: RA18AP03 Categories: , ,

RA18AP03 is the Economy-grade adapter for the 2.92mm male to APC-7 transition: straight body, 18 GHz rating, 50 ohm. The headline figures are a VSWR of 1.25:1 maximum and an insertion loss of 0.20 dB, all specified across the full DC to 18 GHz band rather than at spot frequencies. The gender at each end is stated in the part number; match it against the port or cable it has to meet before ordering. Because the transition happens inside one body, the impedance step is controlled and the part behaves the same way whichever end is connected first. The straight body keeps the run axial, which is the lowest-loss, lowest-stress way to join two ports. It is built in the Economy tier, the value build, keeping the same interface dimensions at a lower price point.

Specifications

  • Interface A: 2.92mm male
  • Interface B: APC-7
  • Frequency: DC to 18 GHz
  • Impedance: 50 ohm
  • VSWR: 1.25:1 maximum
  • Insertion loss: 0.20 dB maximum
  • Body: stainless steel
  • Centre contact: gold-plated beryllium copper centre contact
  • Weight: 0.03 kg
  • Grade: Economy

Where it is used

Field kits carry it because one adapter covers the mismatch between whatever the site has and whatever the instrument expects. Test racks use it to bring a device under test onto an analyser without rebuilding the cable run for every new product.

It is a passive part with no tuning, so it can be swapped in mid-project without re-characterising the rest of the chain.

DC to 18 GHz covers most laboratory traffic, from baseband through the lower microwave bands, and it is the range where this interface family has the deepest catalogue.

Compatibility and mating

2.92mm (K) mates with SMA and 3.5mm mechanically, but the air-dielectric geometry is far less forgiving. Mate only with clean, undamaged interfaces, and do not use a standard SMA connector as a daily partner on a precision port.

Each end keeps its own interface standard, which is why the part number lists both series rather than a single connector type.

Check the interface with a gauge after any drop. A part that has been dropped usually looks fine and measures badly.

Ordering

Custom builds are possible on the same interface pair: different plating, a different flange pattern or a longer body. State the requirement against this SKU and the factory will confirm what can be held.

Frequently asked questions

How many mating cycles will it take?
Precision interfaces are usually rated in the hundreds to a thousand cycles, and the exact figure is in the datasheet. Wear shows first as a rise in return loss.

Can it be mounted to a panel?
Only if the body is a flange or bulkhead type. A straight in-line adapter is not designed to carry panel load; use the flanged version for that.

Is it 50 or 75 ohm?
This part is 50 ohm. A 75 ohm system needs a matching pad or a 75 ohm part; the two impedances are not interchangeable on a threaded interface of the same size.

Why does the price differ from a standard adapter?
Precision tiers hold tighter tolerances and use better materials and plating, which costs more to machine and to test. The tier is part of the part number, not an option.

Will it degrade my VSWR?
Every interface adds a reflection. The guaranteed maximum is in the specifications above, and a good adapter typically measures better than its limit on a calibrated analyser.

RA18AP03 datasheet preview – click to view full PDF

Weight 0.03 kg
Dimensions 6 × 3 × 3 cm
Connector Type

,

Max Frequency

Series

Reviews

There are no reviews yet.

Be the first to review “2.92mm(K,SK) Male to APC-7 Adapter | Economy, DC-18GHz, Stainless Steel”

Your email address will not be published. Required fields are marked *