,

2.92mm(K,SK) Male to 2.92mm(K,SK) Male Millimeter-Wave Ultra-Low Loss Phase-Stable Cable Assembly | Precision, Low Loss, DC-40GHz, with RCA400 Cable

$273.00

+ Free Shipping

A RCA400 build with 2.92mm male and 2.92mm male terminations, RCA400-KMKM-L is specified from DC to 40 GHz. The headline figures are a VSWR of 1.3:1 maximum and an insertion loss of 2.66 dB, all specified across the full DC to 40 GHz band rather than at spot frequencies. Both ends carry pins, so it joins two female ports, typically a cable jack and a bulkhead socket. Both ends are terminated and the assembly is tested as a unit, so its loss and match are known before it is installed. It is built in the Ultra tier, the tightest tolerance class of this interface family, intended for daily precision work.

Specifications

  • Interface A: 2.92mm male
  • Interface B: 2.92mm male
  • Frequency: DC to 40 GHz
  • Impedance: 50 ohm
  • VSWR: 1.3:1 maximum
  • Insertion loss: 2.66 dB/m maximum at 40 GHz
  • Body: passivated stainless steel
  • Centre contact: gold-plated beryllium copper centre contact
  • Weight: 0.15 kg
  • Grade: Ultra

Where it is used

It suits production lines that need every station to measure the same way, with the same electrical length. VNA testing depends on it, because a phase-stable run keeps the reference plane where it was calibrated.

Because the assembly is tested as a unit, the loss and match you design against are the numbers the part actually delivers, not the sum of catalogue figures.

40 GHz is where air-dielectric construction earns its price; a PTFE interface would not hold the match this far up.

Compatibility and mating

The 2.92mm interface is mechanically compatible with SMA and 3.5mm, which is convenient and also the main risk: a worn SMA plug can damage a precision 2.92mm socket. Inspect before every mating and torque to about 0.9 N·m.

The connectors at each end are the series standard, so the assembly mates the same ports and cables as any other part of that series.

Do not use the body as a lever. Side load on a connected cable is what bends centre pins and opens the match.

Ordering

Custom builds are possible on the same interface pair: different plating, a different flange pattern or a longer body. State the requirement against this SKU and the factory will confirm what can be held.

Length is quoted per piece and the assembly is built to it; state the finished length, not the cable cut length, because the connectors consume part of the run.

Frequently asked questions

Can it be repaired?
The ends can usually be re-terminated once if there is cable to spare. For semi-rigid and armoured types, replacement is often faster.

Can I use it outdoors?
The jacket resists moisture, but the connectors need sealing for permanent outdoor use.

Does length change the phase?
Yes, phase scales with electrical length. If phase matters, order to an electrical length tolerance rather than a mechanical one.

Why does the loss figure have a per-metre basis?
Cable loss scales with length, so the datasheet quotes dB per metre at a stated frequency. Multiply by your length and add the connector losses.

How should it be stored?
Coiled at its natural radius with the ends capped. A crushed section shows up later as a bump in the loss curve.

RCA400-KMKM-L datasheet preview – click to view full PDF

Weight 0.15 kg
Dimensions 25 × 20 × 6 cm
Connector Type

Max Frequency

Series

, , ,

Reviews

There are no reviews yet.

Be the first to review “2.92mm(K,SK) Male to 2.92mm(K,SK) Male Millimeter-Wave Ultra-Low Loss Phase-Stable Cable Assembly | Precision, Low Loss, DC-40GHz, with RCA400 Cable”

Your email address will not be published. Required fields are marked *