If your work stays below 6 GHz, almost any decent coaxial connector will do. But once a design climbs into the millimeter-wave range, the connector on the front panel stops being a commodity and starts being a specification. Pick too small an interface and you pay for performance you never use; pick too large a one and your 40 GHz measurement quietly degrades at the launch. This guide explains the four most common precision interfaces — SMA, 2.92mm, 2.4mm and 1.85mm — what each one actually is, how they compare, and how to choose between them without guesswork.

What Each Interface Actually Is
SMA — the workhorse (DC to 18 GHz, extended to 26.5 GHz)
The SMA (SubMiniature version A) is a threaded 50 Ω interface with a 4.13 mm (0.163 in) hex coupling nut and a PTFE dielectric in the mating plane. Standard-grade SMA is rated to 18 GHz; precision SMA variants with tighter tolerances and improved dielectric support reach 26.5 GHz. Because the dielectric sits in the interface, repeatability depends heavily on cleanliness and correct torque — one more reason to use a calibrated torque wrench (typically 8 in-lb, about 0.9 N·m) instead of fingers. Browse our SMA adapters for in-series and between-series conversions.
3.5mm — the air-dielectric bridge (DC to 26.5 / 34 GHz)
The 3.5mm interface replaces the PTFE dielectric with air, which removes the dielectric’s mechanical wear and improves phase stability and VSWR repeatability. It is mechanically compatible with SMA: a 3.5mm connector mates directly with an SMA connector, although the pair then performs to the SMA limit. Our 3.5mm adapters are common in lab environments where SMA test cables meet precision instruments.
2.92mm — the 40 GHz standard (also called K or SMK)
The 2.92mm interface, developed by Wiltron as the “K” connector, keeps the SMA thread geometry but shrinks the air-dielectric interface so the first higher-order mode is pushed beyond 40 GHz. It mates mechanically with SMA and 3.5mm — a genuine convenience in mixed labs — but always verify that the connection’s performance limit (that of the lower-rated half) is acceptable. It is the default front-panel interface on 40 GHz instruments and components. See our 2.92mm adapters and 2.92mm attenuators.
2.4mm — the 50 GHz step (DC to 50 GHz)
Developed by Hewlett-Packard (now Keysight) for 50 GHz network analysis, the 2.4mm interface is not mechanically compatible with the SMA family — the thread and geometry differ deliberately, so a careless SMA cannot be forced into it and damaged. It mates with 1.85mm connectors. If your bench runs a 50 GHz VNA, this is the interface you will touch every day. Our 2.4mm adapters cover in-series and between-series needs.
1.85mm — into V-band (DC to 65 / 67 GHz)
The 1.85mm interface (“V connector”, developed by Anritsu) extends the same air-dielectric philosophy to 65 GHz, with precision grades specified to 67 GHz. It mates with 2.4mm. The interface is small, the tolerances are unforgiving, and a single piece of debris or a bent center conductor can ruin both halves — inspect every mating under magnification. See our 1.85mm adapters.
Selection Table
| Interface | Max frequency | Impedance | Dielectric | Mechanically mates with | Typical use |
|---|---|---|---|---|---|
| SMA | 18 GHz (26.5 GHz precision) | 50 Ω | PTFE | 3.5mm, 2.92mm | General RF, modules, antennas |
| 3.5mm | 26.5 / 34 GHz | 50 Ω | Air | SMA, 2.92mm | Lab instruments, test ports |
| 2.92mm (K) | 40 GHz | 50 Ω | Air | SMA, 3.5mm | 40 GHz instruments, Ka-band |
| 2.4mm | 50 GHz | 50 Ω | Air | 1.85mm | 50 GHz VNAs, Q/V-band R&D |
| 1.85mm (V) | 65 / 67 GHz | 50 Ω | Air | 2.4mm | V-band test, mmWave research |
SMA vs 2.92mm vs 2.4mm vs 1.85mm: The Real Differences
Frequency headroom is the headline, not the whole story
Every interface is usable up to its rated cutoff, but VSWR and insertion loss degrade as you approach it. A good rule: choose an interface rated at least 25% above your highest working frequency. If you measure to 26.5 GHz every day, a 2.92mm chain will outlast and outperform a precision-SMA chain run at its limit.
Mechanical compatibility cuts both ways
SMA, 3.5mm and 2.92mm intermate — convenient, but the weakest half defines the pair, and repeated SMA-into-precision mating wears the precision interface. Dedicated between-series adapters (for example an SMA-to-2.92mm adapter) are the correct way to cross families: they protect the expensive instrument port and are cheap to replace. The 2.4mm/1.85mm pair deliberately does not mate with the SMA family, which prevents accidental damage at 50 GHz-class benches.
Durability and handling
Precision air-dielectric interfaces are typically rated for 500–1,000 mating cycles; SMA is similar in theory but its dielectric degrades faster with abuse. The three habits that decide real-world life are always the same: clean before mating, align before threading, torque with a wrench — never by feel.

Cost scales steeply with size reduction
As a rough market pattern, a precision 2.92mm part costs several times a standard SMA equivalent, and 1.85mm parts cost several times that again. This is why mixed-interface systems are normal: put 1.85mm only where the signal path truly needs 65 GHz, and use adapters to step down to more economical interfaces elsewhere.
How to Choose: A Five-Step Checklist
- Define the real maximum frequency. Use the highest frequency of the measurement or signal, including harmonics you care about — then add 25% margin.
- Check what you must mate with. Instrument ports, cable ends and DUT interfaces decide the family before budget does. An NMD ruggedized test port (see our NMD adapters) is standard on VNA cables precisely so the precision port survives daily mating.
- Prefer between-series adapters over improvisation. Crossing families (N to SMA, SMA to 2.92mm, 2.4mm to 1.85mm) with a specified adapter preserves both the calibration and the hardware.
- Match the rest of the chain. Adapters are only one link: pair them with suitably rated attenuators, coaxial loads and VNA-dedicated cable assemblies, or the best connector in the chain is wasted.
- Budget for consumables. Precision interfaces are wear items. Planning adapter replacement into the lab budget is cheaper than a damaged 50 GHz instrument port.
Frequently Asked Questions
Can I mate an SMA connector directly to a 2.92mm port?
Mechanically yes — the threads are compatible — but the connection then performs to SMA limits (18 GHz for standard grade) and the SMA’s PTFE dielectric will gradually wear the precision interface. For occasional low-frequency checks it is acceptable; for anything regular, use an SMA-to-2.92mm between-series adapter.
Is 2.92mm the same as the K connector?
Functionally yes. “K connector” is Wiltron’s trademark for what became the standardized 2.92mm interface; SMK is Anritsu’s equivalent name. All three refer to the same 40 GHz air-dielectric interface.
Why do 2.4mm and 1.85mm not mate with SMA?
Deliberate incompatibility: the geometry was changed so that a 50 GHz-class port cannot be physically damaged by a mis-threaded SMA. 2.4mm and 1.85mm mate with each other instead.
How much margin should I leave below the rated frequency?
A practical minimum is 25%. Running any interface at its absolute cutoff invites degraded VSWR, repeatability problems and shorter connector life.
Do I need a torque wrench for these connectors?
Yes. Precision interfaces are specified around a defined torque (commonly 8 in-lb for SMA-family and 90 N·cm class wrenches for 2.4mm/1.85mm). Under-torque leaves an air gap that wrecks VSWR; over-torque permanently damages the interface.
RFSPECT stocks in-series and between-series adapters across SMA, 3.5mm, 2.92mm, 2.4mm and 1.85mm interfaces, with datasheets and VSWR specifications on every product page. If your setup mixes families, start from our RF adapter catalog and filter by connector type. Once the interface is chosen, check the VSWR and insertion loss guide before you build the rest of the chain.
Ready-made parts for each interface: if the interface is already decided, these pages list the standard builds with drawings and datasheets — SMA right-angle adapter (RA18S11WH), SMA 20 W fixed attenuator (R12S20-XX), 2.92mm 2 W termination (RT402FX).
About the author — this guide is maintained by the RFSPECT engineering team in Shenzhen, who design and test coaxial adapters, attenuators, terminations and cable assemblies to 110 GHz. If a number here disagrees with the drawing you received, tell us and we will correct it.

