RF & Microwave Glossary: Coaxial Connector and Cable Terms

Thirty-odd terms that come up whenever coaxial adapters, attenuators, terminations and cable assemblies are specified. Each entry is one or two sentences, written for engineers who need the definition rather than a textbook chapter. Where a term has a longer treatment on this site, the entry links to it.

Contents

VSWR (voltage standing wave ratio) · Return loss · Insertion loss · Characteristic impedance (Z0) · Dielectric constant (εr) · Velocity of propagation · Cutoff frequency · Higher-order mode (TE11) · Air line · Bead · Centre pin depth · Mating plane · Coupling torque · Mating cycles (durability) · Semi-rigid cable · Flexible cable · Phase stability · Electrical length · Reference plane · SOLT calibration · TRL calibration · Ripple (in a sweep) · TDR (time-domain reflectometry) · Attenuation (nominal value) · Power derating · Termination (load) · Bulkhead connector · NMD flange · Hermetic seal · Reverse polarity (RP) · Precision vs economy grade · PIM (passive intermodulation) · Directivity (of a coupler or bridge) · Dynamic range

VSWR (voltage standing wave ratio)

The ratio of the maximum to the minimum voltage on a transmission line, caused by a mismatch. VSWR 1.00:1 is a perfect match, 1.15:1 is a healthy precision interface and 2.00:1 reflects 11 percent of the incident power. Read it together with the return loss below.

Return loss

The same mismatch expressed in decibels: RL = −20 log|Γ|, where Γ is the reflection coefficient. Higher is better and the two scales meet at a fixed table — 1.15:1 is 23.1 dB, 1.60:1 is 12.7 dB.

Insertion loss

The power lost between two ports of a passive part, in dB. For cable it is quoted per metre at a stated frequency; for adapters it is usually a few tenths of a decibel to 40 GHz. See the cable selection guide for real numbers by family.

Characteristic impedance (Z0)

The ratio of voltage to current for a wave travelling along a uniform line. Nearly all RF coax is 50 Ω (75 Ω for video and broadcast), set by the ratio of inner to outer conductor diameter and the dielectric.

Dielectric constant (εr)

The relative permittivity of the material between the conductors. Air is 1.0, solid PTFE is about 2.1, and the value sets both the impedance for a given geometry and the velocity of propagation along the line.

Velocity of propagation

The speed of a signal along a cable as a fraction of the speed of light, equal to 1/√εr. Air-dielectric interfaces run at about 1.0, PTFE cable at roughly 0.69 — which is why the same physical length is electrically longer in one than the other.

Cutoff frequency

The frequency above which a coaxial line starts to support higher-order modes instead of the TEM mode it was designed for. It is a property of the cross-section, not of the plating or the quality of the part.

Higher-order mode (TE11)

The first non-TEM mode a coax can carry, which appears once the wavelength approaches the circumference of the line. Above it, loss and VSWR become position-dependent and the measurement stops being repeatable.

Air line

A coaxial line whose dielectric is air (or mostly air), held by a thin bead. Air lines give the lowest loss and the most stable phase, which is why 2.92 mm and smaller interfaces are built this way.

Bead

The small dielectric support that centres the pin inside the connector. Distorting it — by over-torquing the back nut, for instance — changes the impedance at the launch and shows up as a reflection.

Centre pin depth

How far the centre pin sits from the mating plane, measured in tens of micrometres. Too far back leaves a gap; too far forward damages the mating socket. It is the most common defect in a re-terminated assembly.

Mating plane

The reference surface where two connectors meet. Its flatness and cleanliness set the repeatability of every measurement made through it, and it is the surface to inspect before every connection.

Coupling torque

The tightening torque specified for a connector family: 0.9 N·m for SMA, 3.5 mm and 2.92 mm, 0.57 N·m for 1.85 mm and 0.45 N·m for 1.0 mm. See the 1.0 mm care guide.

Mating cycles (durability)

The number of connect-disconnect cycles a connector is rated for before its specified performance degrades. Precision millimetre-wave interfaces are quoted in hundreds, and cleanliness matters more than the count.

Semi-rigid cable

Cable with a solid copper outer conductor that is formed to shape and cannot flex after installation. It holds phase extremely well because it never moves; a bend is a permanent deformation, not a repeated one.

Flexible cable

Cable with a braided outer conductor that tolerates repeated movement. Electrical length changes as it flexes, so its phase stability depends entirely on how the braid and the dielectric are constructed.

Phase stability

How little a cable’s electrical length changes with temperature, flexure and time. Quoted in ppm per °C or degrees per GHz per °C, and the number that decides whether a calibration holds for an afternoon.

Electrical length

The length of a line expressed in degrees or wavelengths at a given frequency, rather than in metres. One metre of PTFE cable is roughly 4.8 ns, which is about 1,730° per GHz.

Reference plane

The physical location to which a VNA calibration refers its measurements — normally the end of the test cables. If the cables change temperature or position, the plane moves and the calibration goes stale.

SOLT calibration

Short-Open-Load-Thru calibration, the standard 12-term method for two-port measurements. Its accuracy depends on the kit definition (the modelled standards), not only on the physical standards.

TRL calibration

Thru-Reflect-Line calibration, which derives the error terms from the fixture itself. More accurate for exotic connectors, but only defined between the frequencies where the line length is usable.

Ripple (in a sweep)

The periodic variation in a frequency sweep caused by two reflections interfering. Its period Δf converts to a distance through Δf = c / (2L√εr), which locates the fault — see the 40 GHz test note.

TDR (time-domain reflectometry)

The time-domain view of the same data: an inverse transform of the sweep that shows reflections as spikes along a distance axis. Modern VNAs compute it from the frequency sweep rather than pulsing the line.

Attenuation (nominal value)

The designed loss of a fixed attenuator, in dB at DC, which stays approximately constant with frequency. The attenuator range is quoted at the top of the band as well, because the two are not the same number.

Power derating

The reduction in a part’s rated power as frequency or ambient temperature rises. A termination rated at 10 W at DC is not a 10 W part at 40 GHz, because the heat path and the resistive film behave differently.

Termination (load)

A single-port resistive element that absorbs incident power and presents a matched impedance. Used to terminate unused ports and as a calibration standard. See the coaxial load range.

Bulkhead connector

A connector designed to pass through a panel or chassis wall, with a flange or threaded body that fixes it mechanically and provides the ground connection to the enclosure.

NMD flange

A bolt-down flange pattern used on millimetre-wave connectors so the interface is held by screws rather than by the coupling nut. It removes torque and side-load from the mating plane, which matters above 40 GHz.

Hermetic seal

A glass-to-metal or ceramic seal that makes a connector leak-tight, used where a pressure or moisture barrier is required. Hermetic parts have slightly different launch geometry and their own return-loss specification.

Reverse polarity (RP)

An interface where the genders are swapped — a plug with a socket contact, a jack with a pin — used to satisfy regulatory requirements on consumer equipment. RP-SMA does not mate with standard SMA.

Precision vs economy grade

Precision parts are air-line interfaces held to tight tolerances and specified to their full band; economy parts use the same thread with looser tolerances and a reduced band. The thread is identical, the performance is not.

PIM (passive intermodulation)

Spurious signals generated when two or more carriers pass through a non-linear junction — a loose contact, corroded plating, or magnetic material in the RF path. Low-PIM parts specify the junction, not just the match.

Directivity (of a coupler or bridge)

How well a directional device separates the forward wave from the reflected one, in dB. In a VNA it limits how accurately a small reflection can be measured in the presence of a large one.

Dynamic range

The span between the largest signal a receiver can handle and the smallest it can resolve, after cable and pad losses. Every attenuator added for protection is subtracted from it.

Where to go next

The interface comparison guide covers which connector families mate and which only look alike; the VSWR and insertion loss primer explains how to read a sweep; the 1.0 mm care guide and the 40 GHz test note cover the handling and measurement side. If a term you need is missing, tell us and we will add it.

About the author — this glossary is maintained by the RFSPECT engineering team in Shenzhen, who design and test coaxial adapters, attenuators, terminations and cable assemblies to 110 GHz.